How to Seal Outdoor Gaps

 
 
 

Landscaping and Outdoor

Outside the home can be just as important as inside the home. As the source of pests and pollen, closing points of entry are vital for those looking to give the home a reprieve from outside disruptors. No matter the gap, Great Stuff™ Multipurpose Black, Great Stuff™ Multipurpose White, and Great Stuff™ Outdoor Foam Sealants provide the protection you need and blend into their surroundings.

Materials

 

 

  • Eye Protection
  • Gloves
  • Drop Cloth
  • Spray bottle filled with water
  • Great Stuff™ product of choice
  • Great Stuff™ Foam Cleaner
  • Serrated knife
 
 
 
 
 
 
  • Step by Step Instructions
    1. Prep area by removing dust and debris.
    2. Shake can for 60 seconds.
    3. Install the dispenser to the product as per directed on the label.
    4. Practice with a dry run.
    5. Invert can and insert it into the gap.
    6. Activate can by pulling the trigger.
    7. Wipe away imperfections with a cloth soaked in Great Stuff™ Foam Cleaner.
    8. Foam should be tack-free in 10 to 15 minutes. If not, mist with water.
    9. Once cured, cut excess foam with a serrated knife as desired.
    10. Store or dispose of product as per directed on label.
    • Mist with water to speed cure.
    • Trim cured foam with serrated blade.
    • Any uncured product that gets on the skin can be removed with acetone.
    • Shake vigorously for a minimum of 60 seconds. If the can sputters, simply shake the can while held upside down.
    • Best results if used when product temperature ranges from 60-90°F (15-32°C). The can should not be exposed to temperatures more than 120°F. Cured foam should not be exposed to temperatures in excess of 240°F.
    • Fill gaps <50%
    • If applied outdoors, be sure to paint or cover foam to prevent discoloration and UV damage.

    Great Stuff™ cans featuring the straw tube applicator will seal shut if left to sit for more than 2 hours after its last use.

    Great Stuff™ cans featuring the Smart Dispenser™ may be reused up to 30 days with the straw left attached to the canister, just clean the tip after your first use. For best results:

    • Thread the Smart Dispenser™ onto the valve until it is secure, ensuring there is no gap between the dispenser and the valve
    • Do not unwind the dispenser after you have started using it.
    • Let up on the trigger slowly to release pressure in the straw and prevent spurts during the next use and to achieve the most consistent bead.
    • Tighten the flow control screw until fully closed for storage. Use can within 30 days of initial use.
    • Store upright with dispenser still attached to can.

    If using Great Stuff Pro™ with Foam Dispensing Gun, follow these additional steps before application:

    • With the can secured, set your desired bead size by adjusting the flow control knob on the back of the gun (bead can be adjusted from 1/8"-3"). Then, pull the trigger to fill the gun with foam, dispensing excess foam into an appropriate waste receptacle. Lastly, test the bead size before applying. 
    • Tighten the flow control screw until fully closed for storage. Use can within 30 days of initial use.
    • Store upright with a foam dispensing gun attached.
    • Always leave a can of foam attached to the gun with the flow control screw closed.
    • When ready to change cans, shake the new can of foam for a minimum of 60 seconds.
    • NEVER leave a gun without a can of adhesive without a can of Great Stuff Pro™ attached unless the gun has been thoroughly cleaned with Great Stuff™ Foam Cleaner.
 
 
 
 
 
 

  • Seal and Insulate up to 1"
  • Black color blends naturally into the surrounding environment
  • Reusable for up to 30 days
  • Seal and Insulate up to 1"
  • Reusable for up to 30 days
  • Maximum Durability
  • Nitrile and latex blend blue disposable gloves
  • Puncture resistant
  • 7.5 mil thickness providing industrial strength